Smart Heating Scheduling & Energy Efficiency
Rooms can be heated above the needed temperature or kept at full comfort settings even when unused. Individual control lets you reduce unnecessary heat demand in selected zones instead of applying a single rule to the entire home.


Where energy waste occurs
Rooms can be heated above the needed temperature or kept at full comfort settings even when unused. Individual control lets you reduce unnecessary heat demand in selected zones instead of applying a single rule to the entire home.
The benefit depends on building insulation, heating source, setpoints, climate and occupant habits; a thermostat cannot guarantee a specific percentage saving.

A sensible schedule for underfloor heating
Underfloor slabs store heat and release it slowly. Large, short-lived changes can make rooms uncomfortable or bring heating demand forward rather than reducing it. Try modest setbacks over meaningful absence periods and observe the actual response of each zone.
Keep rooms with special moisture or comfort requirements within safe, appropriate temperature ranges.
More about the system →
Use room-by-room information
App temperature readings, setpoints and schedules help identify where a room is consistently warmer than needed. Review those settings after changes in weather or daily routine.
Temperature monitoring is not a heat meter. For consumption in kWh or fuel use, separate metering and suitable data are required.

Boiler demand and actuator coordination
When a room reaches its target, its actuator closes after the normal operating delay. The controller can keep the heat source running for other zones that still need heat. Correct sequencing and a properly designed hydraulic circuit matter.
Short cycling, poor balancing or incompatible heat-source wiring can offset expected efficiency gains.
More about the system →
Evaluate changes fairly
Compare similar weather periods and, where available, utility-meter readings before and after a scheduling change. Account for outdoor temperatures and occupancy rather than drawing conclusions from a single day.
The most reliable outcome is a comfortable home with less unnecessary heating, not an advertised universal savings figure.

Scheduling for slow-response floor heating
Underfloor heating stores energy in the floor structure, so it responds differently from a fast electric panel heater. A large temperature reduction at bedtime does not necessarily produce a comfortable or economical next morning. The system may need a long recovery period, depending on the floor build-up, water temperature and outdoor conditions.
Plan the occupied periods first, then make small, gradual schedule adjustments and observe several comparable days. Bedrooms can have different comfort expectations from living areas; a home office may need warmth only during working hours. Avoid choosing a schedule solely because it looks attractive on a phone screen.
The most useful observations are room temperature, target setpoint, recurring overheating and the pattern of actual occupancy. If you need quantified energy savings, compare reliable heat-source or electrical meter readings under similar weather conditions rather than treating app temperature graphs as consumption measurements.
Hydraulic balancing, flow temperatures and building insulation may have greater effects on heating performance than any single app setting. A timer is a tool for matching heat demand to life in the home, not a guarantee of a specific reduction in bills.

Practical installation and commissioning
An effective heating automation project should be checked in the actual building, not judged only by the interface. Record the room, thermostat, heating loop, actuator output and desired schedule. After installation, request heat independently in each zone and verify the correct circuit. Use the official wiring and pairing instructions for electrical and radio equipment; a qualified installer should perform electrical work.
For evaluating comfort changes, observe comparable days and adjust one setting at a time. Underfloor heating responds slowly, and a displayed setpoint does not represent measured consumption. An honest energy comparison requires real meter readings and reasonably similar weather and occupancy.
Build a programme around thermal inertia
Underfloor heating often takes longer than radiators to change room temperature because the floor structure stores heat. Start with modest temperature reductions during longer periods of inactivity, then observe the recovery time. Frequent deep setbacks may reduce comfort and cause long recovery periods without producing the intended savings.
Review your schedules after several days of similar weather. Compare whether rooms reach their required temperature at the right time and whether any zone requests heat unnecessarily. The interface can help manage setpoints and operating schedules, but measuring actual energy savings requires appropriate consumption data from the meter or heat source.
How to verify the result
After making a change, record the previous setting and the reason for it. Check the result across several comparable days rather than judging a slow underfloor system after a few minutes. If comfort deteriorates or rooms begin to overshoot, restore the previous programme and investigate zone balancing, sensor position and boiler operation.
Components and system examples
Q20 Wireless Thermostat for Underfloor Heating AutomationRead guide →
Q30 e-Ink Wireless Thermostat for Underfloor Heating AutomationRead guide →
Q50 Touchscreen Thermostat for Wired Underfloor Heating AutomationRead guide →
Q40 Wired Smart Thermostat for Underfloor Heating AutomationRead guide →
Q10 Wired Thermostat for Underfloor Heating AutomationRead guide →
Installation manuals
Open PDF manual ↗
Open PDF manual ↗Technical guides already published
Frequently asked questions
Where energy waste occurs
Rooms can be heated above the needed temperature or kept at full comfort settings even when unused. Individual control lets you reduce unnecessary heat demand in selected zones instead of applying a single rule to the entire home.
A sensible schedule for underfloor heating
Underfloor slabs store heat and release it slowly. Large, short-lived changes can make rooms uncomfortable or bring heating demand forward rather than reducing it. Try modest setbacks over meaningful absence periods and observe the actual response of each zone.
Use room-by-room information
App temperature readings, setpoints and schedules help identify where a room is consistently warmer than needed. Review those settings after changes in weather or daily routine.
Boiler demand and actuator coordination
When a room reaches its target, its actuator closes after the normal operating delay. The controller can keep the heat source running for other zones that still need heat. Correct sequencing and a properly designed hydraulic circuit matter.
Smart Radiator Valves & Mixed Heating Systems – QTV20
Common Heating Automation Mistakes & How to Avoid Them